S5: XRv Intial Configuration

The IOS XRv router is allready installed in my MacBook as detailed into my recent article Cisco IOS XRv on VMWare Fusion.

As I need a serial connection every time I want to change my LAB setup, I’ve defined my XRv serial connection into Secure CRT as described in the last section of my recent article SecureCRT to XRv Serial Console

0. XRv Network Connectivity

Next I will provide initial configuration for the IOS XRv router to make sure it match the management network design defined for SkyLifter Project.

Network Connected Device Device Port Info IP
vmnet3 XRv Mg0/0/CPU0/0 OoB MNG Net 192.168.83.30/24
vmnet4 XRv-n, n=[1,n] Gi0/0/0/0 Intelink with/without VLANs not configured
vmnet7 XRv-n, n=[1,n] Gi0/0/0/1 Intelink with/without VLANs not configured

As I am new to XRv I will use the Workbook on Cisco Website.

Note: In this moment I don’t know if I can run multimple XRv instances on my MacBook.

The logical network diagram

1. I add the needed networks to XRv VM

From Fusion application, click Ubuntu VM, go to Virtual Machine > Settingsā€¦and add the needed networks.

Then start XRv VM.

2. Connect to XRv Router

I will connect using intial configured user silvia and pass silvia.

Murgescus-MacBook-Pro:~ silvia$ telnet 127.0.0.1 9001
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.


IMPORTANT: READ CAREFULLY
[...]

Please login with any configured user/password, or cisco/cisco


User Access Verification

Username: silvia
Password:

RP/0/0/CPU0:XRv1#

3. Identify physical interfaces

I have defined only 4 physical interfaces which can bee seen into show interface brief command output.

RP/0/0/CPU0:XRv1#show interface bref
Fri Nov 17 19:43:15.580 UTC

Intf Intf LineP Encap MTU BW
 Name State State Type (byte) (Kbps)
--------------------------------------------------------------------------------
 Nu0 up up Null 1500 0
 Mg0/0/CPU0/0 up up ARPA 1514 0
 Gi0/0/0/0 admin-down admin-down ARPA 1514 1000000
 Gi0/0/0/1 admin-down admin-down ARPA 1514 1000000
 Gi0/0/0/2 admin-down admin-down ARPA 1514 1000000

Note: The Mg0/0/CPU0/0 interface is an out-of-band (OOB) management interface. This will always be the first interface associated with the XRv VM as indicated in the XRv installation guide.

4. Configure Management Interface

RP/0/0/CPU0:XRv1#configure terminal 
Fri Nov 17 19:46:42.335 UTC
RP/0/0/CPU0:XRv1(config)#interface M
MgmtEth Multilink 
RP/0/0/CPU0:XRv1(config)#interface MgmtEth 0/0/CPU0/0 
RP/0/0/CPU0:XRv1(config-if)#no shut
RP/0/0/CPU0:XRv1(config-if)#ipv4 address 192.168.83.30/24
RP/0/0/CPU0:XRv1(config-if)#commit
Fri Nov 17 19:48:37.628 UTC
RP/0/0/CPU0:XRv1(config-if)#exit
RP/0/0/CPU0:XRv1(config)#exit


RP/0/0/CPU0:XRv1#show ipv4 interface brief 
Fri Nov 17 19:49:43.543 UTC

Interface IP-Address Status Protocol
MgmtEth0/0/CPU0/0 192.168.83.30 Up Up 
GigabitEthernet0/0/0/0 unassigned Shutdown Down 
GigabitEthernet0/0/0/1 unassigned Shutdown Down 
GigabitEthernet0/0/0/2 unassigned Shutdown Down

5. I check the management connectivity from macOS Local Shell

Let’s try a ping:

Murgescus-MacBook-Pro:~ silvia$ ping 192.168.83.30
PING 192.168.83.30 (192.168.83.30): 56 data bytes
64 bytes from 192.168.83.30: icmp_seq=0 ttl=255 time=3.392 ms
64 bytes from 192.168.83.30: icmp_seq=1 ttl=255 time=0.471 ms
^C
--- 192.168.83.30 ping statistics ---
2 packets transmitted, 2 packets received, 0.0% packet loss
round-trip min/avg/max/stddev = 0.429/1.187/3.392/1.273 ms

Now telnet, as remember that ssh is not working on macOS Sierra:

Murgescus-MacBook-Pro:~ silvia$ telnet 192.168.83.30 
Trying 192.168.83.30...
Connected to 192.168.83.30.
Escape character is '^]'.


IMPORTANT: READ CAREFULLY
Welcome to the Demo Version of Cisco IOS XRv (the "Software").
The Software is subject to and governed by the terms and conditions
of the End User License Agreement and the Supplemental End User
License Agreement accompanying the product, made available at the
time of your order, or posted on the Cisco website at
www.cisco.com/go/terms (collectively, the "Agreement").
As set forth more fully in the Agreement, use of the Software is
strictly limited to internal use in a non-production environment
solely for demonstration and evaluation purposes. Downloading,
installing, or using the Software constitutes acceptance of the
Agreement, and you are binding yourself and the business entity
that you represent to the Agreement. If you do not agree to all
of the terms of the Agreement, then Cisco is unwilling to license
the Software to you and (a) you may not download, install or use the
Software, and (b) you may return the Software as more fully set forth
in the Agreement.


Please login with any configured user/password, or cisco/cisco


User Access Verification

Username: silvia
Password:


RP/0/0/CPU0:XRv1#

Perfect! Now I will be able to connect to management port using telnet into SecureCRT application.

Note: At the moment both vMX and XRv are UP and Running on my MacBook.

Leave a Reply

Your email address will not be published. Required fields are marked *